Used Woodworking Machinery CONTACTS MACHINERY, INC.
200 Round Lake South, Montcalm,
Quebec, Canada, J0T2V0
PHONE: 866-514-0890
Contact Us About This Machine


Costa BAF32 1350

Used Costa BAF32 1350 | Sanders - DeNibbing and Brush






 
Machine Information Sheet Date: 8/17/2018
Inventory #: C3912TS
Machine Type: Sanders - DeNibbing and Brush
Manufacturer: Costa
Model: BAF32 1350
Year: 2008
Region: North East US
Voltage: 480/3/60
Can be transformed to required voltage for a nominal fee. Single phase available thru a phase converter.
Condition: Very Good
Machine Capacities: -Working width: 1350mm
-Standard working thickness up to: 160mm
-Constant pass-line height of feed table from floor: 900 mm
-Lifting/lowering of the frame with the working units with motovariator, power: 0.55 kW
-Over thickness safety in machine entry: a rubber covered roller is connected to micro-switches, thicker work pieces activate the emergency and open up the machine.
-Top machine with mono-block frame; working units positioned in the top part of the frame; feed table at constant pass-line with lifting -lowering of the frame with the working units to enable the easy change of the working thickness.
-Transmission from main motors to working units with v-belts and pulleys, disk brakes on each working unit for emergency stop
-Pressure unit to hold the work pieces on the feed belt, are positioned in front and rear of each working unit, independent variable pressure control.
-Pressure units with rubber covered rollers to hold work pieces on the feed belt, positioned in front/rear of each working unit; rigid of floating to compensate panel thickness differences; equipped with variable pressure control
-The feed table is rigid; the top plate is built in anti-wear steel T1-high resistance; table surface fine-grinded to avoid wear of the internal side of the feel belt.
-Feed belt in rubber; construction in a close loop without joints with various layers of cloth; top profile according to operation requirement
-Drive unit with motovariator controlled by inverter for feed speed variation
-Feed speed variable in continuous: from 4 to 24 ft/min
-In-feed driven roller for connection with machines in line: 60mm diameter
-Out-feed driven roller for connection with machines in line: 60mm diameter

1st working unit:
-FT-3 Flex Trim Brush - useful width 1380mm, with 36 helicoidal sanding inserts: 330mm diameter
-Motor controlled by inverter, for step less cutting speed variation, 2.2 kW power
-O-BS/FT - Oscillating system for SB/FT brushes 330-400 diameter

2nd working unit:
-FT-3 Flex Trim Brush - useful width 1380mm, with 36 helicoidal sanding inserts: 330mm diameter
-Motor controlled by inverter, for step less cutting speed variation, 2.2 kW power
-O-BS/FT - Oscillating system for SB/FT brushes 330-400 diameter

Auxiliary units:
-S180 - Horse hair brush unit for cleaning processed work pieces: 180mm diameter, 1.1 kW power

Auxiliary units:
-SJ1 - Single antistatic bar to unload static electricity

Auxiliary units:
-SR - Rotary blowers for blowing away the dust left by the sanding operation on the surface and on the sides of the panels. Are complete with an auxiliary dust hood

-Electrical plant in a cabinet in the front side of the machine, includes a main switch. Push button panel at side of work
-Pneumatic plant complete with filters - oil/air nebulizer - normal pressure of operation at 6 bar
-Safety pressostat with machine stop when the air pressure drops below a minimum of 4 bar
-Control unit: digital thickness positioning unit for 1 axe, 15 positions of memory with centesimal accurancy. Communication system between Costa machines equipped with PLC (Siemens S7) and other machine with same PLC (Profibus or similar)

THERE ARE TWO IDENTICAL MACHINES AVAILABLE, CAN BE SOLD SEPARATELY.
Sales Price: CALL FOR PRICING

Contacts WW Machinery, Inc. sells pre-owned machinery on a first come, first served basis. Pre-owned machinery is not covered under any warranty or Government requirements. It is purchased "as-is - where-is, with all faults." Descriptions and specifications are to the best of our knowledge (some information is communicated via third party sources). It is strongly recommended that the machinery be inspected prior to purchasing to confirm the condition and specification. Additional charges such as crating and loading may apply.